Announcement

Collapse
No announcement yet.

FS: strong running S50

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • FS: strong running S50

    I recently picked up an S50 (95 M3 engine) last year. I've been holding onto it in hopes that I'd put it into my E36 along w/ a other goodies eventually. It would be really nice but, I just can't feel right allocating the funds to accomplish this in the near future. Other priorities force me to sell this at this time.

    DETAILS
    Pulled from '95 M3 w/ 135k miles. No known issues, was running fine and strong when pulled. I have started to accumulate stuff for this as I was going to freshen everything I could while the engine was out of a car.

    S50 Engine and more
    - Complete S50 top to bottom, intake manifold to exhaust, cam cover to oil pan.
    - Full engine harness OBDI w/ starter
    - Spare extra Engine harness (OBDI)
    - DME - red label 413
    - Spare oil pan
    - transmission cross member for ZF trans
    - intake elbow from TB to AFM and associated vacuum lines
    - misc extras/spares (throw out bearing, tensioner, etc.)

    Upgrades
    - S50 exhaust manifolds ported to match OE gaskets and then professionally ceramic coated black

    NEW! stuff For S50 (gaskets, seals, etc.)
    - Headgasket (Erling)
    - Set of head bolts (Reinz)
    - Set of lock nuts (6) for guibo for ZF E36 trans from M3/328
    - Rear Crankshaft Seal
    - Rear Main Seal
    - Oil Filter Housing To Block Gasket
    - Oil Dipstick O-Ring, For Dipstick Tube
    - Oil Dipstick O-Ring
    - Intake Manifold Gaskets (6)
    - Exhaust Manifold Gasket to head (3)
    - Gasket Rings, Catalytic Converter to Rear (2)
    - Exhaust Manifold to Catalyzer Pipe gaskets (2)

    Needs (to make complete)
    - Alternator
    - AFM
    - Airbox/intake forward of AFM
    - Any other gaskets/seals/sensors you want to replace or other maintenance
    - Valve cover gasket set
    *this list does not include anything specific to fitting this S50 to an E30 or other chassis.

    If interested, email me : [email protected]

    PRICING
    - $2100 O.B.O. : as it sits in it's current state, w/ all the gaskets/seals/etc in a box.
    - $2650 O.B.O. : with all applicable gaskets/seals listed above installed.

    SHIPPING IS EXTRA and at the BUYER's EXPENSE.
    PICKUP/DELIVERY available within a certain distance. If you pick up, engine stand is free for the taking.

    *can also get valve cover powder coated for buyer for additional expense (will need gasket set in advance if you want me to install)

    Thanks - Jon
    Jon D. Simmons
    1988 E30 M3 - STX #88
    AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

  • #2
    Some partial trades will be considered. Inquire via email.

    Thanks - Jon
    Jon D. Simmons
    1988 E30 M3 - STX #88
    AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

    Comment


    • #3
      I know this guy. He actualy has my "Real" M3 in his garage. There for a while I was wondering if i would see this motor in my car! LOL

      The engine looked pretty clean to me... Someone should buy it...
      Chris Conant
      13th place Trophy Solo 2 National Championships 2004
      3rd Place Trophy Solo 2 National Championships 2008
      12th place Trophy Solo 2 national Championships 2010
      Bimmer Brothers Racing
      Want to save on oils and make a few bucks?
      Amsoil
      :fire:

      Comment


      • #4
        Thanks Chris,

        You know if you'd like it in your car, I could accommodate you
        Jon D. Simmons
        1988 E30 M3 - STX #88
        AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

        Comment


        • #5
          where r u located???

          Comment


          • #6
            I am located in Gretna, NE

            Use 68028 or 68114 for shipping estimates.
            Jon D. Simmons
            1988 E30 M3 - STX #88
            AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

            Comment


            • #7
              Hi,
              I am interested but I would need to verify the mileage. How do you know the donor M3 had 135k miles on it? Do you have the vin# of donor M3 so I can verify the mileage through carfax?
              Thanks
              sigpic
              1989 M3 Cabriolet "Reproduction" #787th?? :-)

              Comment


              • #8
                I don't have VIN. Not sure how to verify any other way. Sorry.
                Jon D. Simmons
                1988 E30 M3 - STX #88
                AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

                Comment


                • #9
                  Vin is not on the head? Last one I purchased still had VIN tags.
                  Who knows where I'll be, changes from day to Continent.

                  Comment


                  • #10
                    I will check tonight...
                    Jon D. Simmons
                    1988 E30 M3 - STX #88
                    AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

                    Comment


                    • #11
                      did get pics & vin...

                      but it is now sold.
                      Jon D. Simmons
                      1988 E30 M3 - STX #88
                      AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

                      Comment


                      • #12
                        STILL AVAILABLE - buyer backed out. :(

                        PICS w/ VIN : http://picasaweb.google.com/jon.d.si...JKOjY73w4WB_gE

                        Last edited by GotCone?; 05-18-2009, 02:10 AM.
                        Jon D. Simmons
                        1988 E30 M3 - STX #88
                        AST-USA | Bimmerworld | Butler's C&D | D-Force | Russ' Garage | Import Specialists

                        Comment

                        Working...
                        X